my s13 - Drifting forum

damo_s13 · 02-10-2006, 18:08

well decided to start a thread about my s13 its norris desgins old shell i got form braba

so my s13 is going a bit more drifty now but will still have silly power i think

so far i got hold of/done

VEMS ecu still doing wiring for this to be fitted. It is getting there tho as seen in pic. this is the wiring for hole car!

Had my head cleaned, ported and new stem seals fitted

Had my crank polished and balanced

Fitted some new bushers and white line arbs

heat wraped my manifold

Got my self a new inlet manifold. Pic is of my new manifold on old onwers car. thanks buffy (sxoc)

Fitted a new fuel pump as old one was getting very load and on its way out

think thats about it for now

be about 8week before it back on the road

damo

pablo13 · 05-10-2006, 17:41

So far so good

RandomGuy · 06-10-2006, 09:23

good going mate

PhatBob · 06-10-2006, 10:21

Damo, good to see some more pics of the project, it will be the first VEMS controlled CA18's

What's interesting is that in this pic:

Quote:

Originally Posted by damo_s13

You can see that the guy has gone for a Bosch Motorsport wasted spark coil pack (Bosch part number: 0-221-503-407) I've been looking at these recently because they're a better bet than the coil on plugs.

Also looking at the pics of Sumo's new drag car, they've gone for a Coil Near Plug setup.

I think I'm going to use the Bosch Motorsport coil pack TBH.

Rob

damo_s13 · 09-10-2006, 23:43

yeah i've looked at that but will use the stock stuff to start with i think.

thats buffys old engine from sxoc

got the inletmanifold here now very nice

damo

PhatBob · 10-10-2006, 08:04

Quote:

Originally Posted by damo_s13

yeah i've looked at that but will use the stock stuff to start with i think.

thats buffys old engine from sxoc

got the inletmanifold here now very nice

damo

Its easy to change the coil types later.

Whats the inside of the manifold like?

damo_s13 · 14-10-2006, 07:19

inside its big lol what info you after? i can see each inlet to block goes about 10mm inside into the manifold

damo

damo_s13 · 12-11-2006, 00:20

quick update on my s13. old engine/box plus lots of old wiring now out cleaning the engine bay up tomorrow and start to fit the new wiring i've got/started to do for the vems. will get some pic's.

Also i have got new rims on the way

from al's junk yard

there 17" Work RYVER. 2x 17"x8" ET35 for front and 2x 17"x9" ET38 for the rear

drax · 12-11-2006, 01:18

Where do you get ur boost / breather / vaccume piping / hoses from?

damo_s13 · 12-11-2006, 17:22

pmed you

damo_s13 · 12-11-2006, 17:54

well started on the engine bay cleaning today but allso go a quick look at my engine block with the pistion in

anyway back to the engine bay, dirty

clearner

then started on the wiring, its a mess lol

will carry on with it tomorrow
damo

damo_s13 · 12-11-2006, 19:17

wiring for vems started

VEMS unit, egt sensor, a/f sensor and map semsor

wiring to the stock coil pack

wiring to the injectors

Paul FWx · 12-11-2006, 19:29

Hi matey

The plans were alwya good, nice to see youll be using it properly

Ill keep an eye out for the new pics

Steve_Be · 13-11-2006, 11:45

Looking good mate

damo_s13 · 16-12-2006, 11:09

thanks bud

update-------------------------------------

im losing my unit so my project is now called get running asap be on road by end of jan only 300hp (ish) @ whhels tho due to only using a case treated rb20/ca18 combo gearbox lol

on a good note got my self some raod legal slicks for a little grip work later in year. i love ebay!!!

Yokohama tyres Advans 235/45/17

i've also got new bling i/c pipe work an a new oilpump on the way from apex performance. a big gay carbon spoiler (1550mm wide) and canrads to help with downfoce/turn in now i dont have as much power lol

i've also binning my graphic so will just be the writing down the side and a few sticks.... driftworks/sc to be added

damo

damo_s13 · 23-12-2006, 23:10

well got an email saying my 256 tommi poncams will be with me on the 2nd on jan

also my injectors are on there way got to love ebay

534cc sard injectors (new in the box) should see me over 300hp @ wheels for only £160 inc del

damo

damo_s13 · 28-12-2006, 17:11

well today i..................

finshed off what wiring i could do without the engine in.

de spoilered

and fitted a new Stainless steering bush from driftworks.

damo

damo_s13 · 03-01-2007, 20:44

today i had a good day on the s13

i got loads done realy...

i did have 2 Corbeau boss seat mounted using stock frames that were customised. this rased you up about 1/2 inch

plus i needed an fia approved seat if i ever want to compete so i riped them both out today as i got my self some more goodies

i fited the drivers side seat in the passager with a proper frame from corbra had to drill 2 holes but it fitted fine lower that the old ones too

with the drivers seat now out of the way i started on the wiring under the dash

all done

yey its getting closer not to much left now

damo

Hammond · 03-01-2007, 20:47

Looking good dude

spin-king · 03-01-2007, 21:28

Getting there matey.

That spoiler looks alot like mine where did you get it from???

02-10-2006, 18:08	#1 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	my s13 vems powered well decided to start a thread about my s13 its norris desgins old shell i got form braba so my s13 is going a bit more drifty now but will still have silly power i think so far i got hold of/done VEMS ecu still doing wiring for this to be fitted. It is getting there tho as seen in pic. this is the wiring for hole car! Had my head cleaned, ported and new stem seals fitted Had my crank polished and balanced Fitted some new bushers and white line arbs heat wraped my manifold Got my self a new inlet manifold. Pic is of my new manifold on old onwers car. thanks buffy (sxoc) Fitted a new fuel pump as old one was getting very load and on its way out think thats about it for now be about 8week before it back on the road damo Last edited by damo_s13 : 21-03-2007 at 00:48.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-10-2006, 17:41	#2 (permalink)
pablo13 Piston Melter Join Date: Aug 2006 Location: London/Essex Border Posts: 340	So far so good

06-10-2006, 09:23	#3 (permalink)
RandomGuy Team Japspeed Join Date: Aug 2005 Location: Manchester Posts: 6,953	good going mate

09-10-2006, 23:43	#5 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	yeah i've looked at that but will use the stock stuff to start with i think. thats buffys old engine from sxoc got the inletmanifold here now very nice damo

14-10-2006, 07:19	#7 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	inside its big lol what info you after? i can see each inlet to block goes about 10mm inside into the manifold damo

12-11-2006, 00:20	#8 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	quick update on my s13. old engine/box plus lots of old wiring now out cleaning the engine bay up tomorrow and start to fit the new wiring i've got/started to do for the vems. will get some pic's. Also i have got new rims on the way from al's junk yard there 17" Work RYVER. 2x 17"x8" ET35 for front and 2x 17"x9" ET38 for the rear

12-11-2006, 01:18	#9 (permalink)
drax GFX / Web Dude Join Date: Jan 2005 Location: Sittingbourne, Kent Posts: 2,176	Where do you get ur boost / breather / vaccume piping / hoses from?

12-11-2006, 17:22	#10 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	pmed you

12-11-2006, 17:54	#11 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	well started on the engine bay cleaning today but allso go a quick look at my engine block with the pistion in anyway back to the engine bay, dirty clearner then started on the wiring, its a mess lol will carry on with it tomorrow damo

12-11-2006, 19:17	#12 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	wiring for vems started VEMS unit, egt sensor, a/f sensor and map semsor wiring to the stock coil pack wiring to the injectors

12-11-2006, 19:29	#13 (permalink)
Paul FWx RB > SR Join Date: Jan 2006 Posts: 1,435	Hi matey The plans were alwya good, nice to see youll be using it properly Ill keep an eye out for the new pics

13-11-2006, 11:45	#14 (permalink)
Steve_Be Sidelined Join Date: Jul 2005 Location: Teesside Posts: 1,102	Looking good mate

16-12-2006, 11:09	#15 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	thanks bud update------------------------------------- im losing my unit so my project is now called get running asap be on road by end of jan only 300hp (ish) @ whhels tho due to only using a case treated rb20/ca18 combo gearbox lol on a good note got my self some raod legal slicks for a little grip work later in year. i love ebay!!! Yokohama tyres Advans 235/45/17 i've also got new bling i/c pipe work an a new oilpump on the way from apex performance. a big gay carbon spoiler (1550mm wide) and canrads to help with downfoce/turn in now i dont have as much power lol i've also binning my graphic so will just be the writing down the side and a few sticks.... driftworks/sc to be added damo

23-12-2006, 23:10	#16 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	well got an email saying my 256 tommi poncams will be with me on the 2nd on jan also my injectors are on there way got to love ebay 534cc sard injectors (new in the box) should see me over 300hp @ wheels for only £160 inc del damo

28-12-2006, 17:11	#17 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	well today i.................. finshed off what wiring i could do without the engine in. de spoilered and fitted a new Stainless steering bush from driftworks. damo

03-01-2007, 20:44	#18 (permalink)
damo_s13 hope to drift soon Join Date: Aug 2005 Location: sheffield Posts: 969	today i had a good day on the s13 i got loads done realy... i did have 2 Corbeau boss seat mounted using stock frames that were customised. this rased you up about 1/2 inch plus i needed an fia approved seat if i ever want to compete so i riped them both out today as i got my self some more goodies i fited the drivers side seat in the passager with a proper frame from corbra had to drill 2 holes but it fitted fine lower that the old ones too with the drivers seat now out of the way i started on the wiring under the dash all done yey its getting closer not to much left now damo

03-01-2007, 20:47	#19 (permalink)
Hammond oh, snap! Join Date: Jan 2005 Location: Canterbury Posts: 4,961	Looking good dude

03-01-2007, 21:28	#20 (permalink)
spin-king dorifto kingu! Join Date: May 2006 Location: wirral (merseyside) Posts: 1,688	Getting there matey. That spoiler looks alot like mine where did you get it from???