AW11 Drift Project - Page 4 - Drifting forum

Irishtwincam · 30-08-2007, 10:12

Twos R Us - Exclusive Distributor for High and Tight Motorsports

These chappies will KNOW what you need!

Quote:

Originally Posted by gtst lad

Thanks mr twincam i'll have a nose on the ebay for one, think i did spot one the other day actually.

gtst lad · 04-09-2007, 15:14

Thanks matey

Small update.

Cut springs were a huge fail with capital F, so have ordered a new set to replace them.

Also started work on sorting the rotten arches so as when i do finally find some sweet offset wheels i'll be able to roll metal arches rather than just chiselling filler

Cut and ground back to good metal.

Zinc primed ready to weld on new panels.

Irishtwincam · 04-09-2007, 15:45

Toyota MR2

Repair arches to suit the AW11 MR2, anything else you need?

gtst lad · 04-09-2007, 15:55

Damn i'm living in the wrong country, they're cheap.
I've already got all the panels sitting here though

cefiro_drifta · 04-09-2007, 22:58

why were the springs a fail ???

gtst lad · 04-09-2007, 23:04

It totally destroyed the handling, i'm guessing it effected the spring rate to a point that the car turned into a mid engined pogo stick

cefiro_drifta · 04-09-2007, 23:27

hahah funny stuff... how muhc lower were the springs then ?

gtst lad · 05-09-2007, 07:09

They were about 35mm, then i lowered it another 70mm ish

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-09-2007, 15:14	#62 (permalink)
gtst lad Ut oh Join Date: Apr 2005 Location: Queensland, Australia Posts: 2,141	Thanks matey Small update. Cut springs were a huge fail with capital F, so have ordered a new set to replace them. Also started work on sorting the rotten arches so as when i do finally find some sweet offset wheels i'll be able to roll metal arches rather than just chiselling filler Cut and ground back to good metal. Zinc primed ready to weld on new panels.

04-09-2007, 15:45	#63 (permalink)
Irishtwincam Tá me sasta :D Join Date: Jun 2005 Location: Cambs Posts: 491	Toyota MR2 Repair arches to suit the AW11 MR2, anything else you need?

04-09-2007, 15:55	#64 (permalink)
gtst lad Ut oh Join Date: Apr 2005 Location: Queensland, Australia Posts: 2,141	Damn i'm living in the wrong country, they're cheap. I've already got all the panels sitting here though

04-09-2007, 22:58	#65 (permalink)
cefiro_drifta mad pointing munkey Join Date: Oct 2005 Location: surrey Posts: 12,122	why were the springs a fail ???

04-09-2007, 23:04	#66 (permalink)
gtst lad Ut oh Join Date: Apr 2005 Location: Queensland, Australia Posts: 2,141	It totally destroyed the handling, i'm guessing it effected the spring rate to a point that the car turned into a mid engined pogo stick

04-09-2007, 23:27	#67 (permalink)
cefiro_drifta mad pointing munkey Join Date: Oct 2005 Location: surrey Posts: 12,122	hahah funny stuff... how muhc lower were the springs then ?

05-09-2007, 07:09	#68 (permalink)
gtst lad Ut oh Join Date: Apr 2005 Location: Queensland, Australia Posts: 2,141	They were about 35mm, then i lowered it another 70mm ish