bee r rev limiter - Drifting forum

bez · 02-07-2008, 18:39

hi just got one of these to day off e bay.any how the wiring is diffrent to my last one just wanted to no if any one has had the same problem.
my wireing colours are red, black, green, black/white, red/white. wire dose look like it as been cut down as its a used item.can any one help

bez · 02-07-2008, 19:05

can any 1 help is the loom in 2 parts

monster R32 · 02-07-2008, 19:12

mine was red,white,black,green,yellow,grey

red for power...
white for launch control...
green angle sensor...
yellow other angle sensor..
grey for the engine type...

the loom is in one part and the grey wire should be near the box cut or uncut other wires at the end

there is a page on here with fitting instructions on it go to home then into resorces.....

bez · 02-07-2008, 19:37

hi all the other ones iv fitted are as you have put.but not this 1.colours are as stated in my first post.no one else had this problem?

monster R32 · 02-07-2008, 19:39

nope maybe they have changed the model/design do you have any pics etc

bez · 02-07-2008, 19:46

ill post them now

bez · 02-07-2008, 19:54

wire colour from left to right is:green ,black/white, red/white, red, black

monster R32 · 02-07-2008, 19:54

ok buddy

monster R32 · 02-07-2008, 20:04

looks to me that all the wires are the same as normal but just a different bloody colour witch doesnt help you out much i would say in your case it goes

all red = power
all black = negative
green = an angle sensor but unsure witch
red/white = other angle sensor
then the black/white goes to the handbrake witch is optinal...

apart from that its just going to be trial/error just remember that the gain nobb is set to 0 so if you leav it like this it wont work so move it to about 4 then go from there

bez · 02-07-2008, 20:13

thanx for that ill look in to it bloody thing iv had 6 of these now none with colours like this.lol

skyline · 02-07-2008, 20:23

what are the numbers on the back??

bez · 02-07-2008, 20:42

no numbers on it

bez · 02-07-2008, 20:43

says kvc 36 on wire.and e162205

bez · 02-07-2008, 21:10

no one else got any ideas dont want to guess as i may blow summat up.lol

monster R32 · 02-07-2008, 21:19

sorry dude im out of options

bez · 02-07-2008, 21:22

thanks for all the help any how.

podge07 · 02-07-2008, 23:26

r these save on a engine

02-07-2008, 18:39	#1 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	bee r rev limiter hi just got one of these to day off e bay.any how the wiring is diffrent to my last one just wanted to no if any one has had the same problem. my wireing colours are red, black, green, black/white, red/white. wire dose look like it as been cut down as its a used item.can any one help

02-07-2008, 19:12	#3 (permalink)
monster R32 mr braudside Join Date: Feb 2008 Location: west midlands Posts: 515	monster R32 mine was red,white,black,green,yellow,grey red for power... white for launch control... green angle sensor... yellow other angle sensor.. grey for the engine type... the loom is in one part and the grey wire should be near the box cut or uncut other wires at the end there is a page on here with fitting instructions on it go to home then into resorces..... Last edited by monster R32 : 02-07-2008 at 19:14.

02-07-2008, 19:39	#5 (permalink)
monster R32 mr braudside Join Date: Feb 2008 Location: west midlands Posts: 515	monster R32 nope maybe they have changed the model/design do you have any pics etc

02-07-2008, 19:54	#8 (permalink)
monster R32 mr braudside Join Date: Feb 2008 Location: west midlands Posts: 515	monster R32 ok buddy

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-07-2008, 19:05	#2 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	can any 1 help is the loom in 2 parts

02-07-2008, 19:37	#4 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	hi all the other ones iv fitted are as you have put.but not this 1.colours are as stated in my first post.no one else had this problem?

02-07-2008, 19:46	#6 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	ill post them now

02-07-2008, 19:54	#7 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	wire colour from left to right is:green ,black/white, red/white, red, black

02-07-2008, 20:04	#9 (permalink)
monster R32 mr braudside Join Date: Feb 2008 Location: west midlands Posts: 515	looks to me that all the wires are the same as normal but just a different bloody colour witch doesnt help you out much i would say in your case it goes all red = power all black = negative green = an angle sensor but unsure witch red/white = other angle sensor then the black/white goes to the handbrake witch is optinal... apart from that its just going to be trial/error just remember that the gain nobb is set to 0 so if you leav it like this it wont work so move it to about 4 then go from there

02-07-2008, 20:13	#10 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	thanx for that ill look in to it bloody thing iv had 6 of these now none with colours like this.lol

02-07-2008, 20:23	#11 (permalink)
skyline dorifto kingu! Join Date: Oct 2006 Posts: 797	what are the numbers on the back??

02-07-2008, 20:42	#12 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	no numbers on it

02-07-2008, 20:43	#13 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	says kvc 36 on wire.and e162205

02-07-2008, 21:10	#14 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	no one else got any ideas dont want to guess as i may blow summat up.lol

02-07-2008, 23:26	#17 (permalink)
podge07 tail slider Join Date: Mar 2007 Location: portlaoise ireland Posts: 96	r these save on a engine

02-07-2008, 21:19	#15 (permalink)
monster R32 mr braudside Join Date: Feb 2008 Location: west midlands Posts: 515	sorry dude im out of options

02-07-2008, 21:22	#16 (permalink)
bez gripper Join Date: Jul 2008 Posts: 10	thanks for all the help any how.