Needed Urgently - Drifting forum

bell · 28-06-2008, 19:21

Nissan S13 200sx Sump To Fit Ca18 Det
Please P.m Myself Or Jdmash As Car Is Sitting On Drive With Holes In The Sump

Cheers All

Bell

superclarkey · 28-06-2008, 19:25

haha, did the rods exit the engine

lol

bell · 28-06-2008, 19:27

NO MATE ASH HAS DECIDED TO PLUMB A OIL TEMP UNIT IN ONLY PROBLEM THE TAP OUT OF HIS SET WAS THE WRONG SIZE DISCOVERED AFTER DRILLING A HOLE doh!

DO YOU HAVE ONE MR CLARKEY?

superclarkey · 28-06-2008, 19:28

why don't you weld the sump up ?

and no, sadly not.

superclarkey · 28-06-2008, 19:30

or wait until monday and buy the tap you need... did you drill the pressed steel part of the sump !?!

bell · 28-06-2008, 19:32

he has welded it up then he thought of a way he could do it, done that and the sender unit snapped

only problem is its sitting on my drive and he live 10 miles away

bell · 28-06-2008, 19:33

oh and the tap is a 10mm . 1 hard as frick to get.... to the point where a friend who owns an engineering firm hasnt even got one

special order only

matt22robbins · 28-06-2008, 19:41

Hi mate,

I have 2, if you want one give me a call on 07920853579 i wil be about tomorrow, my address is
9 astley walk
temple herdewyke
southam
warwickshire
cv47 2un

£20 and can have your pick of the 2 i have?

cheers

Matt

jdmash · 28-06-2008, 20:53

hi matt. thanks am very intrested. i have no transport thats all. has any1 got one closer. thanks

28-06-2008, 19:21	#1 (permalink)
bell MATT DAMON!! Join Date: Feb 2006 Location: wolverhampton, west mids Posts: 546	Needed Urgently Nissan S13 200sx Sump To Fit Ca18 Det Please P.m Myself Or Jdmash As Car Is Sitting On Drive With Holes In The Sump Cheers All Bell

28-06-2008, 19:41	#8 (permalink)
matt22robbins touge runner Join Date: Mar 2008 Posts: 151	Re: sump Hi mate, I have 2, if you want one give me a call on 07920853579 i wil be about tomorrow, my address is 9 astley walk temple herdewyke southam warwickshire cv47 2un £20 and can have your pick of the 2 i have? cheers Matt

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

28-06-2008, 19:25	#2 (permalink)
superclarkey ______________ Join Date: Aug 2004 Posts: 9,249	haha, did the rods exit the engine lol

28-06-2008, 19:27	#3 (permalink)
bell MATT DAMON!! Join Date: Feb 2006 Location: wolverhampton, west mids Posts: 546	NO MATE ASH HAS DECIDED TO PLUMB A OIL TEMP UNIT IN ONLY PROBLEM THE TAP OUT OF HIS SET WAS THE WRONG SIZE DISCOVERED AFTER DRILLING A HOLE doh! DO YOU HAVE ONE MR CLARKEY?

28-06-2008, 19:28	#4 (permalink)
superclarkey ______________ Join Date: Aug 2004 Posts: 9,249	why don't you weld the sump up ? and no, sadly not.

28-06-2008, 19:30	#5 (permalink)
superclarkey ______________ Join Date: Aug 2004 Posts: 9,249	or wait until monday and buy the tap you need... did you drill the pressed steel part of the sump !?!

28-06-2008, 19:32	#6 (permalink)
bell MATT DAMON!! Join Date: Feb 2006 Location: wolverhampton, west mids Posts: 546	he has welded it up then he thought of a way he could do it, done that and the sender unit snapped only problem is its sitting on my drive and he live 10 miles away

28-06-2008, 19:33	#7 (permalink)
bell MATT DAMON!! Join Date: Feb 2006 Location: wolverhampton, west mids Posts: 546	oh and the tap is a 10mm . 1 hard as frick to get.... to the point where a friend who owns an engineering firm hasnt even got one special order only

28-06-2008, 20:53	#9 (permalink)
jdmash dorifto kingu! Join Date: Jan 2008 Location: Wolvohampton Posts: 587	hi matt. thanks am very intrested. i have no transport thats all. has any1 got one closer. thanks