Complete Air Cup Kit with 14mm Cups

More Views

Complete Air Cup Kit with 14mm Cups

£533.33

From £18.32 a month on finance (based on £640.00 Purchase) *Subject to Terms and Conditions
From £18.32 a month on finance (based on £640.00 Purchase) *Subject to Terms and Conditions
Worldwide Shipping Get a quote

For those people that want to run proper coilover suspension with the ability to lift the car over obstacles; The future is here!

The Stanceparts Air Cup Kit includes everything you need to install the air cup lift system:
• 2 or 4 air cups (depending on the option chosen)
• 12 meters of airline & T-splitter(s) (To suit both Front and Four-corner setups)
• 12v 3-way valve + switch and 5 meters of wire
• Complete VIAIR compressor kit with 2 gallon tank.
• Instructions Booklet


This kit will fit the current design of HSD kits for the following models:
(If you already own a HSD kit, please measure your current shaft diameter to confirm application)


Honda Civic EG6 EH Fork Type 92-95 - HSD Monopro
Honda Civic EK EM MB6 EJ9 96-00 - HSD Monopro
Honda Civic EM2 ES1 ES2 EP1 EP2 01-05 - HSD Monopro
Honda S2000 AP1 AP2 00-09 - HSD Monopro
Infinity G35 V35 03+ - HSD Monopro
Lexus GS300 92-97 - HSD Monopro
Lexus GS300 98-05 - HSD Monopro
Lexus IS200 IS300 99+ - HSD Monopro
Lexus SC300 92-00 - HSD Monopro
Lexus SC430 UZZ40 01+ - HSD Monopro
Mazda RX7 FD3S 93-96 - HSD Monopro
Nissan 300ZX Z32 90-96 - HSD Monopro
Nissan 350Z Z33 03+ - HSD Monopro
Nissan Skyline R32 GTR BNR32 88-94 - HSD Monopro
Nissan Skyline R32 GTS HCR32 88-94 - HSD Monopro
Nissan Skyline R33 GTR BNR33 95-01 - HSD Monopro
Nissan Skyline R33 GTS ER33 93-98 - HSD Monopro
Nissan Skyline R34 4WD ENR34 98-02 - HSD Monopro
Nissan Skyline R34 GT Non Turbo 98-02 - HSD Monopro
Nissan Skyline R34 GTR BNR34 98-02 - HSD Monopro
Nissan Skyline R34 GTT ER34 98-02 - HSD Monopro
Nissan Stagea 2WD 96-01 - HSD Monopro
Nissan Stagea 2WD M35 01-07 - HSD Monopro
Nissan Stagea 4WD 260RS & Hicas 96-01 - HSD Monopro
Nissan Stagea 4WD Non Hicas Eyelet 96-01 - HSD Monopro
Nissan Stagea AWD NM35 01-07 - HSD Monopro
Toyota Altezza SXE10 99+ - HSD Monopro
Toyota Aristo S140 91-97 - HSD Monopro
Toyota Aristo S160 97–05 - HSD Monopro
Toyota Chaser JZX100 96-01 - HSD Monopro
Toyota Chaser JZX90 92-96 - HSD Monopro
Toyota JZX110 Mark 2 - HSD Monopro
Toyota Supra JZA80 93-98 - HSD Monopro
Toyota Supra MA70 86-92 - HSD Monopro


If you have any queries regarding air cup fitment, be sure to contact us!


2 year warranty on the air cups.
1 year warranty on the compressor setup, covered by the manufacturer: VIAIR.


Please Note: The images depict both the front only kit and the full kit with optional rear cups.

Air cup Kit!
1 x 14mm Shaft Diameter Air Cups [Pair] - In Stock
  • 1
    £250.00
Description

Details

These Stanceparts air cup kits will fit a lot of coilover kits with the exception of some large diameter inverted dampers. - Get in touch if you're unsure about your kit.

The kit sits between the main spring and the spring top cup on the coilover and is just 20mm when not inflated. At full extension the cups measure approximately 70mm, so provide approximately 50mm of lift. 
Stiff spring rates can reduce how much the kit lifts, and helper springs or spring droop are sometimes recommended when fitting these cups, so they are not fighting the main spring rate too much in addition to the weight of the car.

When used with HSD & Driftworks Coilovers we have a variety of parts & springs available, so will do our best to assist in making this kit work correctly as best as possible. With other coilover brands additional parts may be required that we may not be able to source.


FITMENT REQUIREMENTS
The air cups should fit any brand of coilovers, as long as they meet the requirements below.
Make sure the dimensions match your coilover, we strongly recommend to measure with a caliper. You will also need to ensure you have adequate clearance on your car to support the cups.


MEASUREMENTS

measurements Springs
• The outer diameter must be less than 99mm.
• The inner diameter must be 61 mm or more.

Coilover shaft
• Measure the thickest part of the coilover shaft. Kits are available for coilover shaft diameters:12,5mm, 14mm, 15mm, 16mm, 18mm, 20mm and 22mm

SPRINGS

measurements

Linear springs
The air cup lift system will only fit on linear springs, it will not fit on ''shaped'' springs as shown in the figure. If you have ''shaped'' springs, it's often possible to install linear springs.

High spring rates
If you're using extreme high spring rates, higher than the original rates that came with your coilovers, then it's possible that you can't use the full 50mm lift from the air cups. Due to the extreme high spring rates, the weight of the car won't compress the springs and damper enough to create a stroke for the air cups to lift. This can be solved by using helper springs. 

DIMENSIONS

measurements

• The diameter of the air cup is 120 mm.
• The fitting is 17mm.


The air cup is only 20mm thick in the lowest position. Depending on your coilovers and vehicle, the air cups will generally take up 20 to 30mm of space. If you have enough travel left on your coilovers to lower it, this won't be a problem. If not, you can install shorter springs to compensate.

HOW DOES IT WORK?

measurements

The air cup is mounted on the top of the spring and just acts like a spacer. When you put pressure in the system, the air cup will expand and the car will raise up to 50mm. The air cup lift system does not affect the ride quality and performance of your coilovers.

• Max total car weight: 2000 kg / 4400 lbs (or max axle weight: 1300 kg / 2850 lbs)

Shipping Price

Shipping Price

We ship worldwide!
  • Yes No
Finance

Finance Calculator

Reviews

No Reviews

Get the latest product releases & offers...
Top