1JZ engine, single turbo, low mileage

Thread in 'Parts for sale' started by Yorke, Jul 11, 2015.

  1. Yorke

    Yorke Member

    Joined:
    Jun 3, 2010
    Posts:
    358
    Likes Received:
    0
    Ok so I'm guaging interest, if this sells, then I'll break the rest of the car, BUT, no other parts will be sold until I have cash for the engine.

    So there is no point asking me about other parts on the car yet. Don't even bother.


    I rebuilt this engine September 2014, there were no known faults with this engine, I killed my engine and had this as a spare, it was easier to rebuild this one and know that I had a good engine as it had stood a while.

    I've probably done less that 2000 miles since rebuild, due to clutch problems, gearbox problems, and misfire problems (turned out to be a fucked injector, now resolved)

    specs:
    full toyota gasket and seal set
    oem head gasket
    oem head bolts
    acl big end bearings
    arp rod bolts
    head skimmed
    valves lapped etc
    oem water pump
    oem timing belt kit
    thermostat
    A/c delete
    aux belt
    Rebuilt alternator
    good stater

    Borg Warner turbo with rebuilt core
    hks external gate, 0.8bar spring
    heat wrapped down pipe
    excesively long screamer pipe
    unknown exhaust manifold (welded once - tiny area)
    braided oil feed and return

    370cc injectors (440s were fucked)
    fuel pressure reg blanked for adjustable for (not inc)
    Adjustable cam pulleys (set to standard)
    Oil filter sandwich plate
    hockey puck engine mounts
    magnetic sump plug
    cheap oil catch can
    trd oil cap

    Engine loom
    standard ecu
    map sensor
    coil packs
    any other essential parts

    almost everything was painted when I built it, including:
    rocker covers
    block
    upper sump
    lower sump
    external waste gate
    Oil filter housing
    engine mounts


    its been running on emanage ultimate (not included) at 1.0 bar, until yesterday, I turned the boost up to 1.3, still with good air/fuel ratio.
    currently using valvoline vr1 5/50

    obviously I can do a comp test for anybody, this was kinda wrote on a whim.

    the engine is fitted in the car, the pictures of the engine on the stand was before I put the engine in. Though that is almost exactly how it's being sold and what will be fitted. I encourage anybody to come and have a good look at the engine, see it running, let me take them for a test drive etc.

    this does have a manual w58 gearbox fitted to it, but no running gear is included, no clutch, no flywheel etc etc.

    Radiator and intercooler are also not included


    price £2000 firm



    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]
     
  2. Yorke

    Yorke Member

    Joined:
    Jun 3, 2010
    Posts:
    358
    Likes Received:
    0
    Bump up
     
  3. tion

    tion Member

    Joined:
    Jan 12, 2013
    Posts:
    298
    Likes Received:
    0
    What size thread did you use for the hockey puck mounts
     
  4. vetrondrift

    vetrondrift Member

    Joined:
    Aug 11, 2010
    Posts:
    88
    Likes Received:
    0
    Mate I will take the lot I can come pick up soon as u let me no where you are.can you txt me as really on here 07710261464
     
    #4 vetrondrift, Jul 14, 2015
    Last edited: Jul 14, 2015
  5. Yorke

    Yorke Member

    Joined:
    Jun 3, 2010
    Posts:
    358
    Likes Received:
    0
    Deposit received, provisionally sold!
     

Share This Page